Chat with Us:+86-15362698302 Email Us:[email protected] Call Us:+86-13712873191

Get a Free Quote

Our representative will contact you soon.
Email
Name
Mobile/WhatsApp
Company Name
Message
0/1000

Double-Layer Drawer Box: Two Trays, One Pull

Time : 2026-11-04

A two-piece gift set usually means two boxes, two cartons and two unboxing moments. This rigid drawer box carries both layers in one sleeve: pull the ribbon and the second tray travels out with the first.

Double-Layer Drawer Box: Two Trays, One Pull

What the 31-second clip shows

Five captions carry the whole sequence, and the opening motion you see is the same motion your customer will make.

  • 0:00 — "Luxury Drawer Box." The closed box on a white surface, full-wrap print on the sleeve.
  • 0:05 — "Logo hot stamping." The foil mark catches the light as the box turns in the hand.
  • 0:09 — "Ribbon handle." A ribbon loop is hooked with one finger and pulled.
  • 0:17 — "Lower layer expands automatically." The second tray arrives as the first one clears.
  • 0:21 — "Double-layer drawer." Both trays open side by side, inserts exposed.

Half a minute, start to finish. That is the entire unboxing.

Two layers, one box

Where a second layer earns its cost is the set sold as one SKU: a perfume with its travel spray, a serum above its cream, a candle with its matches, a necklace over its earrings, a box of chocolates with the card on top. In each case you design one box, store one box, pack one box and ship one carton line — instead of two of everything.

There is a second reason. A single-layer box gives the recipient one moment. Two trays give a sequence: the first layer is the product, the second is the extra. That sequence is what gets filmed on a phone at the kitchen table, and it is the part of a gift set people describe when they recommend it.

Two die-cut insert trays open side by side in a double-layer drawer box

The pull is the design

A finger notch is the default way to open a drawer box. It costs a die-cut through the front panel, and it interrupts whatever is printed there. A ribbon does the same job from outside the print: the front face stays whole, the ribbon can be matched to the brand colour, and the first move of the unboxing is explicit rather than fumbled.

On the sample here the ribbon is a flat woven tape in a colour taken from the artwork. It is stitched and glued into the drawer board, not surface-applied, so it takes the load of a full tray.

Ribbon handle being pulled to open a rigid drawer box

Foil outside, print inside

The sleeve is printed full-colour and finished with a hot-stamped logo — the mark reads as metal against the print and changes as the box is turned, which CMYK alone does not do.

The inner panel of the sleeve is printed too, and this is the part most buyers leave blank. In the sample on camera it carries the factory's certificates and production figures, so the buyer reads them at the exact moment the box is open. On your project that panel is your artwork: a scent note, care instructions, a serial number, a thank-you line. It is the cheapest printed area in the box, and the one the recipient is looking at.

Why a sleeve is worth re-printing

The printed sleeve is a separate piece from the trays and the inserts. That matters on repeat orders: when a seasonal or limited-edition artwork changes, the change lands on the sleeve, while the rigid structure behind it stays as it is. Whether tooling and set-up carry over is confirmed per project — but the construction is what makes the option possible at all.

If you run the same gift box in several colourways a year, that is the structure to compare against a fully wrapped box.

The trade-off you should price in

A rigid box ships built. Two trays inside a sleeve take more carton volume than the same print on a flat sheet, so if your freight per unit is already tight, this is not the structure to default to.

Two comparisons are worth running on your own size and quantity: a folding rigid box, and our flat-pack lid-and-base box, which collapses to a fraction of its assembled footprint. We calculate the volume difference per project rather than quote a blanket percentage, because the answer depends on box size, board combination and shipping method.

Fully custom, MOQ 500 pcs

Size, board, sleeve print, foil area, ribbon colour and insert cavities are all made to your artwork — this is not a stock box, and the city artwork on camera is one customer's design, not a range.

Minimum order quantity for customized packaging is 500 pcs. OEM and ODM projects are both welcome. Jiurun Packaging is FSC certified, ISO 9001 certified and Sedex audited, with a 10,000 m² factory in Humen, Dongguan, 6 handmade assembly lines, 4 automatic lines and a capacity of more than one million boxes per month.

Tell us what goes in each layer

Send us three things: what sits in the top tray, what sits in the bottom, and the outer dimensions you need. We will come back with a structure proposal, a check on which areas can be foiled, and a quote. Artwork and a sample follow once the details are confirmed — 1 to 3 days on standard requests.

Related: Drawer Box · Box Inserts · Rigid Gift Box · Perfume Box · Jewelry Box · Candle Box

double layer drawer box two trays one pull-0

Get a Free Quote

Our representative will contact you soon.
Email
Name
Mobile/WhatsApp
Company Name
Message
0/1000